Hey Ho. I do not want to log-in as service, I just want to remotely log-in to the web interface, to do whatever an operator does, without the headache of using the panel of a ZX, for instance. I thought that it would be a common knowledge, not secret by Christie Digital itself. But, in any case, I wouldn't want to brake any forum rules. Will do as you suggest. Thank you in advance. Thank you for your help.
This is my mail: azabuhome hotmail. It does not start automatically. From a terminal program I think it is "vnc 1" you have to use the quotes. Make sure you are using port or in your terminal program. I forget which it is right now. The S1 tpc is very simple, and anyway he doesn't have the tpc. The S2 tpc is a wee pc running Windows XP "embedded" In this case, clear the Use PCF checkbox. A vertical adjustment is typically required when using a z-screen.
However, older lamps may not always strike at the lowest power settings. Select the channel from the drop-down list and click Copy to apply the Channel changes. Repeat for every channel that requires the same ILS values. Choose from hour or standard hour formats. Time is always displayed on each window in the chosen format.
Time Zone - Choose the time-zone. The value at the top of the meter is shown in arbi- trary units-of -measure and does not represent actual lumens or fL. Hours Enter the number of hours logged on the newly installed lamp.
Each motor can either be reset individually or select All Axes when prompted to reset the 4 motors in suc- cession. List of test patterns that are Click to transfer selected available from the Main menu. Restore Cancel new unsaved source settings of resolution, offset and aspect ratio. Test Apply current settings to the image without saving. Restore will not cancel a Save. Restore Cancel new unsaved screen settings and return to previously saved settings.
Non-Letter Box and-bottom or left-and- right—will be discarded. See Save Notes below. Restore This button enables you to return to the gamut menu settings that were present when you opened the menu. See Restore Notes below. For special applications in which you want to create a unique target color standard, enter new TCGD coordinates as desired and then save as a new TCGD file.
Apply as usual from the Channel: Page 2 menu. Address specific to SNMP network management sys- tem. Reboots the TI software. Select to close all commu- nication pipes with the TI firmware. This is used to install new TI software. Click Apply to save the Max FL value. Once Apply is clicked, the Max Power button becomes unchecked and the Apply button becomes greyed-out.
Lamp power returns to the lamp power it was before Max Power was clicked. Perform the regular software load to go from v2. Once the downgrade is complete, reboot the Figure Failsafe Web Application projector by clicking the Reboot button in the failsafe web application. Figure Once the downgrade is complete, reboot the projector by clicking the Reboot button in the failsafe web application. The downgrade from 2. The power reverts back to what was originally defined in the menus by the user.
Also make sure to follow all the criteria specified in Section 2. Repeat Steps as necessary. Repeat Steps , but reading at the screen instead of at the lens. It is a good idea to periodically recalibrate footlamberts Figure NOTE: Frame rate multiplication less than may flicker at slow incoming frame rates. Try reversing the current setting.
Single 3D Input Not Working A single source signal containing both left and right data is not currently supported. Also supported is the YCbCr progressive input with 10 bits per components and a pixel format of x at This arrangement is the most flexible of all.
The extremely high brightness can cause permanent eye damage. Lamps may explode if dropped or mishandled. Page Maintaining Proper Cooling 4.
Check the coolant level every 6 months, by removing the air filter door and viewing it through the grille. Use caution when handling. Do not ingest. Page Maintenance And Cleaning - use the tension in the folded cloth itself to collect dust. If significant dust is still bound to the surface, dampen a clean microfibre cloth with coated optics cleaning solution damp, not dripping. Wipe gently until clean. Vacuum loose dirt from the lamp fan impeller. If necessary, use a brush with hot water and suitable detergent.
Igniter Clean the high voltage terminal and insulator to remove accumulated dust or dirt. The lamp fan vane switch is located within the lamp cooling compartment. The extractor vane switch is located just inside the top duct on the projector lid. Check and clean the switches to remove accumulated dust or dirt that could impede movement if necessary. Page If you are installing any other lamp type, make sure this extension nut is removed. The purpose of the extension nut is to correctly position the lamp for opti- mal light output.
Never operate the projector without the filter installed. Always discard used air filters. Page Troubleshooting NOTE: A qualified service technician is required when opening an enclosure to diagnose any probable cause. If you do not hear anything, it may indicate a problem with the igniter Christie service required.
On the web user interface Main menu, Douser Open should be enabled 5. Ensure a full black test pattern is not selected for display. Is the correct display file selected?
Verify the correct cinema port is connected for this display file. Page The Display Is Faint 1. Check leveling of the projector.
Ensure the lens surface and screen are parallel to one another. Is the vertical offset correct? Adjust as necessary using the vertical offset knob. Is the anamorphic lens straight? Rotate to orient aperture correctly. This can be implemented via the Channel: Page 1 menu of the web user interface by disabling the Cinema checkbox.
0コメント